Sunday, February 24, 2013

How to Assemble a PC

How to Assemble a PC
If Previously I discussed the basics about computers, now let's learn how to assemble a good PC. actual hardware installation for PC series is not difficult to do, besides there are motherboard manual that we can when we embroider a motherboard, pemasagan any computer hardware vendors such didesaign by its simple, my goal to help us in the installation. it's time we start learning to assemble a PC.

for those of you who want to learn without attending private lessons or courses, please look at the following steps carefully:the initiation of a PC assembly we need to prepare are:
Parent board computer / motherboard, use a mother board that has slots to accommodate SATA Harddrive / SATA CDRoom types, such as the motherboard still has a slot for IDE PATA Hard Drive Types
    
processors
    
RAM
    
Hard Drive
    
CD / DVDRoom
    
Chasing + Power Supply
    
Operating system installation CD
    
Drivers also prepare the motherboard
The following step-by-step hardware installation kompuer / Assemble PC:
Installing the Motherboard Processorif you install the processor on the motherboard is said to be the hardest thing, then that statement I say "ONE" we put the processor on the motherboard must match the existing processor slot on the motherboard, and processor socket number of jeis prsesor itself. put the processor in the processor slot on the motherboard, the processor meletakkanya find the corner of the pin it is not full, the condition will be the same as the form of processor slot on the motherboard so it is very unlikely that we made a mistake when putting the processor, see Figure 1after the processor is put, do not forget to lock the processor (to lock the processor on the motherboard many different forms depending on the motherboard)give gel pad on the processor before you put the CPU Cooler Aboveput CPUCooler + Fan / CPU fan on the processor and CPU Cooler is the key (remember CPUCooler be locked with Meetings
Installing RAMPair RAM Slot On The Motherboard ersedian RAM (RAM type should be the same as the type of RAM the motherboard slot) to set indentation note held by each of RAM and make sure when putting a position parallel to the ridge indentations found on the RAM slot, it is technically correct if peletakanya RAM will lagsung terkunci.lihat picture 2
Putting On Chasing PC Motherboardplace your motherboard has been installed into the processor and RAM Chasing, install the bolt, bolt especially close to the goal that RAM when removing / replacing the RAM, motherboard under pressure and not too curved, it may lead to fractures and a bus on the motherboard off
Replacing the hard drive and CD / DVDRoom
attach hard drive and CD / DVDRoom in place in Chasing PC, lock the bolt to the meeting, the meeting less hard drive installation will cause the hard drive is easy to shake and cause mechanical errors that interfere with the performance of Head Disk
Installing the Power Supply Cable
Power Motherboard
New versions are generally for the motherboard, power cable to be installed there are 2, power 24 Pin and 4 Pin
Power Cables installed hard drive and CDRoom
If we use manifold Harddisk SATA, we just need to set it up and lock denan Bolts, but if we use hard drive PATA manifold, then we need to pay attention Jumper the hard drive, change the jumpers on the hard drive Master position, so that when in use operate, Hard can get a schedule Access Perama this time can help speed up your computer kiinerja.completely plug the power cable to the hard drive and CDRoom suplly
Connect each Fan / Fan existing power supply
remember, Fan installation try to have one facing outward to perfect the circulation going, because if all Fan Chasing him into it does not create air circulation
Replacing Hard Drive Data Cable and CDRoomPair Data Cables in accordance with the type Haddisk or CDRoom, PATA Or SATAif the hard drive that kta using SATA type, my suggestion to connect the hard drive to the first SATA SLOT motherboard
Replacing the Front PanelFront Panel PIN is usually located on the corner of the motherboard which serves to activate the buttons and indicators on the front ampu Chasing, totaling 9 Pin. Pin 1 and 2 LEDs for Power, Pin 3 and 4 for Switch Power / PWR SW, Pin 5 and 6 for the HDD LED and Pin 7 and 8 for the Reset Switch / Reset SW
Installing A USBA USB function USB utuk additional menaktifkan for Chasing, located near the Front Panel Pin 8 Pin numbered



after all installed perfectly, cover Chasing the right, once again not to get one bolt (lock) the loose

Computer Basics - Software and Hardware

Computer BasicsIn general, the computer can be interpreted as a calculating device, to sense in general, computer system is a series of systems that include hardware, software and brainware. where it is the third component of a computer that is coupled into a single unit of work that are interconnected to perform various operations programs.
Hardware

is a computer hardware that functions as a machine worker, processing and producing machines.Major computer hardware, including:
Processor 

The processor is the most important organ in the brain as a computer which enabled computers, hardware plays a role in every process performed by the computer, the greater the ability of the processor, the more the process can be done in the not too distant.

Motherboard

The motherboard is the main papad computer that serves as the parent string of computers that connect each computer component into a set of hardware that is ready to workRAM (Random Access Memory): RAM is the computer's main memory is temporary, which means that everything stored in RAM is lost when the computer is not being alive.Disk: Disk is a computer storage media in a permanent, hard drive functioned to store the operating system, applications and all files in the computer. 
Software (Programs)in a series of computer system software to differentiate into 2, namely:
Operating System, is a program that is used to connect between Hardware and Brainware, where the operating system will serve to facilitate the communication between hardware and Brainware. examples of operating systems such as DOS, Apple, Linux, Windows etc..Applications, is a program that comes with the commands that can be selected by Brainware for in execution by the operating system hardware through an intermediary. examples of applications between Ian M. office, Winnamp, browser etc.. 

Brainware (User)is user / user to operate the computer to get a result in the form of files. brainware computer can be:
man, where the man who acted as a regular user called operatorAnother engine, another system is a device that can be connecting with computer and give commands to be processed by a computer

7 things you should know basic computer learning

Here are 7 things you should know basic computer learning: 

1. ComponentYou should know the components of a computer. Must know the specifications of your computer.Additionally you have to know what the function of each component of the computer. No need to get too detailed components. Quite a few rudimentary components like processors, RAM, hard drives, and video cards. A little basic knowledge of additional components that are used will also help. For example, on the keyboard, mouse, monitor, etc.. 

2. DesktopEach time the computer turned on, you will see the desktop. Do not underestimate the desktop. Know your desktop. Learn the basic functions of the desktop.Many tricks and tips desktop will facilitate your work. For example, create a shortcut, making pinned programs, set the display tray icon, maximize the functions on the start menu, etc..Believe me, you will be greatly helped by a good knowledge of desktop. 

3. SoftwareAt this point, you have to learn the basic steps of using the software. For example, about running an application, create a new document, open an existing document, save a document, and print documents.It would be useful if you know how to install and how to uninstall the software. Both of these are the most often overlooked. Most people just want the origin of life. Do not want to know how to "install" and "uninstall" software. Consequently if need a piece of software, they do not know what to do, bother looking for help.Learning computer would be incomplete without knowing the install and uninstall. This is basic stuff. 

4. Computer MaintenanceEven if you use a computer properly, not all kinds, never plug in flash, for sure one day you will have a slow computer.The cause of a slow computer is a variety. Could be because too many temporary files are created, too many start up the application, the hard drive is too full, viruses, etc..Therefore, it is important to perform computer maintenance. Minimal is a treatment system.For hardware maintenance, I suggest that you do it carefully. Or if you are not sure, leave this task to a computer technician. If you are one of the treatment, the hardware could be damaged. Remember, the price of computer hardware is not cheap.If the computer system is damaged, the hardware is not necessarily broken. And for current service rates faulty computer system about 50 thousand. As with if the hardware is broken. If the hardware is damaged, most likely your computer can not be used again. Hardware purchase costs could reach hundreds of thousands. 

5. TweakingIt may even have been treated on a regular basis, but still slow computer. If so you can do the tweaking.With tweaking, the ability of the computer can be upgraded and customized to your liking.For tweaking, you can do things like change a theme, voice, screen resolution, up to tweaking the configuration further. 

6. Computer VirusSooner or later, you will surely be met with a computer virus.Therefore, you must have knowledge of good antivirus. Choose the right antivirus. Know the standard features available on the antivirus and how to remove the virus. Do not let you use advanced antivirus but did not know how to use it. 

7. TroubleshootingWhen your computer error, you should be able to handle it. Minimal to computer problems that often occur.If there is a problem, do not immediately run to find help or a service. Try to think creatively, where the problem occurs. Then think, about what things are associated with that section. Keep on thinking and narrow your thinking to find the root of the problem.After the meet, find a solution. To find a solution, use the internet. I'm the same way. Every problem there is a computer / laptop, I always run to the internet first. When it dead ends, I am new to the service.(What is troubleshooting?)The key is ...Learning computers must think creatively. As I mentioned above, do not immediately think of asking for help from others. If at any time the person is far away from us, then how? You'll hassles.Nowadays a lot of information scattered on the internet. Take advantage of the internet. For example, three years I very often encounter computer problems (because I like tooling for fun: D), but I have not been to a service. I'm just having internet only. If my computer can not for the internet, I borrowed a friend's computer to find a solution my computer problems.Such tips that I can give to learn computers. You have any other suggestions about learning computers? Tell. Let's learn together.

Computer Basics


Know the basics of computer keyboard key usabilityHere is a description of the functions of the keyboard: 
Ctrl + A = (All)used to select the whole object either drawings or text on the worksheet in the block Ms Word for everything.Ctrl + B = (Bold) Create a sentence that is blocked or selected to be bold. 
Ctrl + C = (Copy) to copy a word or phrase that also functions duplicate the selected text or image
Ctrl + D = (Font) Displays Form to change the font size and adjust the shape and type of font / font 
Ctrl + E = (Center) Make sentences mean ketenga blocked into a paragraph 
Ctrl + F = (Find) Displays Form for column search function to search for a word or phrase 
Ctrl + G = (Go To) Displays Form Find and Replace go to to get to the desired page 
Ctrl + H = (Replace) Displays the Replace Form which is to replace certain words 
Ctrl + I = (italic) letters to Making italics 
Ctrl + J = (Justify) to make the left and right in paragraph 
Ctrl + K = (hyperlink) Displays the Insert Hyperlink Form that serves to link his / linking text 
Ctrl + L = (Left) Create a script to the left 
Ctrl + M = (Indent) Make a left indent a little jutted into. serves to shift First Indent, Hanging Indent Left Indent and simultaneously to the right in a paragraph 
Ctrl + N = (New) Create a new page / open a new worksheet in MS Word 
Ctrl + O = (Open) Function to open a MS Word document on a worksheet 
Ctrl + P = (Print) Displays the print menu to print documents on a printer 
Ctrl + Q = Restore like first
Ctrl + R = (Right) Showing sentence that blocked a flush right 
Ctrl + S = (Save) to save the script or text in MS Word worksheet 
Ctrl + T = Creating a hanging indent 
Ctrl + U = (Underline) Make underline sentences blocked.Ctrl + V = (Paste) Displays the copied word or phrase
 Ctrl + W = Close the Microsoft Word screen 
Ctrl + X = (Cut) Serves to move text or an image, followed by the paste command
 Ctrl + Y = (Redo / Repeat) To return to the command that has been canceled 
Ctrl + Z = (Undo) Returns like first 
Ctrl + 0 = make the step down
Ctrl + 1 = To set the size of the first line spasing on pragraf (single) 
Ctrl + 2 = To set the size of the line spasing 2 on pragraf (double) 
Ctrl + 5 = To set the size of the line spasing 1.5 on pragraf+ Ctrl + = Make a sentence on a small script that blockedCtrl + {= Enlarging text on the block or in multiple selection by 1 pxCtrl +} = Decrease text in the block or in multiple selection by 1 pxCtrl + F1 = Display form Getting started
 Ctrl + F2 = Display text in paper form to the printer before printing 
Ctrl + F4 = Closes a document and return kedokument before if you work with multiple document 
Ctrl + F5 = Constructing display Microsoft Word into a medium-size 
Ctrl + F6 = Create screen to minimize 
Ctrl + F9 = Make advance brackets and parentheses 
Ctrl + F10 = Create down restore and maximize 
Ctrl + F12 = Display the OpenCtrl + Alt + 1 = Making a sentence hurupnya print larger sizes
.Ctrl + Alt + 2 = Making a sentence in italics hurupnya and larger size. 
Ctrl + Alt + 3 = Restore to normal.Ctrl + Shift + + = Displays a script which was blocked up 
Ctrl + Shift + 8 = Creates enterCtrl + Shift + = Decrease text in the block or in the selection with multiples of 2 pxShift + F3 = To change Sentence case, lowercase, uppercase and Capitalize the selected text turnsAlt + R = Displays in print or print preview 
Alt + F4 = Exit Application For Ms Word

Thank you for visit Study Computer Science

History and Development of Computer


History and Development of Computer - Considering there is a saying that does not know it was lovethen we should know before approaching about what we know or or learn more inThe history begins with the development of computer discovery a man named Charles Babbage. He is a scientist in the world who have much to contribute to human life, especially the development of computers.
The discovery is phenomenal computing machine (Difference Engine No. 1) is one of the most famous discoveries in the history of the computer and is the first automatic calculator as the embryo kompuer. The discovery was made as the inventor Charles Babbage konpur and dubbed the father of the computer.
Here is the history of computers and its development:
1822: Charles Babbage proposed his idea of ​​a tool that can assist humans in performing calculations at a high level of complexity and complex. Machines buatanya unfinished is currently on at the Museum of Science musiumkan London.
1937: Dr. John V Atanasoff and Clifford Berry began making the first electronic digital computer design. They gave the name of the machine is the ABC (Atanasoff-Berry Computer). ABC engine capabilities are limited only count added and reduction.
1943: In World War 2, An English scientist named Alan Turing designed electronic computers made specifically for the British army. The purpose of making the computer so they can be used to penetrate the German defenses code.
1944: Howard Hathaway Aiken (American) made named Mark I. Is a digital countdown computer first. The computer has a 7.45 feet x 50 feet, with a weight of 35 tons. Mark I have can be used to calculate the probability.
1945: Dr. John von Neumann wrote a concept of data storage. At the time, was an idea.
1946: Dr. John W. Mauchly and J. Presper Eckert, jr. make the first large-scale computer, the computer name is ENIAC (Electronic Numerical Integrator And Computer). The world also considers these two as the inventor of the digital computer.





Computer ENIAC weighed 30 tons, consisting of 18,000 light tube (transistor size), with a width of 30 feet x 50 feet, using 160,000 watts of power. When first operated First of all electricity in the Philadelphia region unexpectedly died.

ENIAC was a little more advanced than the Mark I, which is only able to calculate. ENIAC not only have the ability to count, add, less, times, for, but can also be programmed to perform a simple process.

1951: The U.S. Bureau of Cencus installed the first commercial computer called the UNIVAC I (Universal Automatic Computer). UNIVAC I was developed by Mauchly and Eckert for the Remington-Rand Corporation.

1947: William Shockley, John Bardeen, and Walter Brattain is the inventor of the world's first transistor. Since ditemukanya transistors, computers become increasingly smaller sizes.

Similarly, the history of computer development is derived from a variety of sources.

Thank you for your visit to Study Computer Science