Sunday, February 24, 2013

How to Assemble a PC

How to Assemble a PC
If Previously I discussed the basics about computers, now let's learn how to assemble a good PC. actual hardware installation for PC series is not difficult to do, besides there are motherboard manual that we can when we embroider a motherboard, pemasagan any computer hardware vendors such didesaign by its simple, my goal to help us in the installation. it's time we start learning to assemble a PC.

for those of you who want to learn without attending private lessons or courses, please look at the following steps carefully:the initiation of a PC assembly we need to prepare are:
Parent board computer / motherboard, use a mother board that has slots to accommodate SATA Harddrive / SATA CDRoom types, such as the motherboard still has a slot for IDE PATA Hard Drive Types
    
processors
    
RAM
    
Hard Drive
    
CD / DVDRoom
    
Chasing + Power Supply
    
Operating system installation CD
    
Drivers also prepare the motherboard
The following step-by-step hardware installation kompuer / Assemble PC:
Installing the Motherboard Processorif you install the processor on the motherboard is said to be the hardest thing, then that statement I say "ONE" we put the processor on the motherboard must match the existing processor slot on the motherboard, and processor socket number of jeis prsesor itself. put the processor in the processor slot on the motherboard, the processor meletakkanya find the corner of the pin it is not full, the condition will be the same as the form of processor slot on the motherboard so it is very unlikely that we made a mistake when putting the processor, see Figure 1after the processor is put, do not forget to lock the processor (to lock the processor on the motherboard many different forms depending on the motherboard)give gel pad on the processor before you put the CPU Cooler Aboveput CPUCooler + Fan / CPU fan on the processor and CPU Cooler is the key (remember CPUCooler be locked with Meetings
Installing RAMPair RAM Slot On The Motherboard ersedian RAM (RAM type should be the same as the type of RAM the motherboard slot) to set indentation note held by each of RAM and make sure when putting a position parallel to the ridge indentations found on the RAM slot, it is technically correct if peletakanya RAM will lagsung terkunci.lihat picture 2
Putting On Chasing PC Motherboardplace your motherboard has been installed into the processor and RAM Chasing, install the bolt, bolt especially close to the goal that RAM when removing / replacing the RAM, motherboard under pressure and not too curved, it may lead to fractures and a bus on the motherboard off
Replacing the hard drive and CD / DVDRoom
attach hard drive and CD / DVDRoom in place in Chasing PC, lock the bolt to the meeting, the meeting less hard drive installation will cause the hard drive is easy to shake and cause mechanical errors that interfere with the performance of Head Disk
Installing the Power Supply Cable
Power Motherboard
New versions are generally for the motherboard, power cable to be installed there are 2, power 24 Pin and 4 Pin
Power Cables installed hard drive and CDRoom
If we use manifold Harddisk SATA, we just need to set it up and lock denan Bolts, but if we use hard drive PATA manifold, then we need to pay attention Jumper the hard drive, change the jumpers on the hard drive Master position, so that when in use operate, Hard can get a schedule Access Perama this time can help speed up your computer kiinerja.completely plug the power cable to the hard drive and CDRoom suplly
Connect each Fan / Fan existing power supply
remember, Fan installation try to have one facing outward to perfect the circulation going, because if all Fan Chasing him into it does not create air circulation
Replacing Hard Drive Data Cable and CDRoomPair Data Cables in accordance with the type Haddisk or CDRoom, PATA Or SATAif the hard drive that kta using SATA type, my suggestion to connect the hard drive to the first SATA SLOT motherboard
Replacing the Front PanelFront Panel PIN is usually located on the corner of the motherboard which serves to activate the buttons and indicators on the front ampu Chasing, totaling 9 Pin. Pin 1 and 2 LEDs for Power, Pin 3 and 4 for Switch Power / PWR SW, Pin 5 and 6 for the HDD LED and Pin 7 and 8 for the Reset Switch / Reset SW
Installing A USBA USB function USB utuk additional menaktifkan for Chasing, located near the Front Panel Pin 8 Pin numbered



after all installed perfectly, cover Chasing the right, once again not to get one bolt (lock) the loose

No comments:

Post a Comment